Rheem Error Code A061: Fan Speed Error
Warning: Your Rheem HVAC system has encountered a fan speed error. It's safe to use, but needs professional attention.
How to Fix Rheem Code A061
- Check if the fan is running at all. If not, try resetting the system by turning off the power at the thermostat and the main panel, then turning it back on after 30 seconds.
- Inspect the fan control board for any visible damage or signs of overheating. If you're not comfortable doing this, it's best to call a professional.
- When to call a pro: Always if you suspect an electrical issue, or if the fan still isn't working after a reset.
How to Reset Rheem Code A061
- Turn off the unit using the power button on the front panel.
- Turn off the gas supply valve.
- Turn off the circuit breaker supplying power to the unit. Wait 30 seconds.
- Restore power at the breaker, then open the gas valve.
- Turn the unit back on. If the error returns, the underlying issue needs repair.
Resetting clears the code from the display but does not fix the underlying fault. If the code returns after reset, proceed to the diagnostic steps above.
What Does Rheem Error Code A061 Mean?
The Rheem A061 error code indicates that your HVAC system's fan isn't operating at the correct speed. This could be due to a faulty fan control board, a problem with the fan motor itself, or an issue with the system's wiring. The fan may run too fast, too slow, or not at all. While the system is still functional, it's important to address this issue to maintain optimal performance and prevent further damage.
Common Causes
- Faulty fan control board
- Problem with the fan motor
- Wiring issue in the system
- Incorrect fan speed setting in the system's programming
Diagnostic Steps
| If... | Check | Expected |
|---|---|---|
| Fan is not running | Measure voltage at the fan motor terminals with the system off | 0 volts |
| Fan is running but at incorrect speed | Check the fan control board for any visible damage or signs of overheating | No damage or overheating |
| Fan control board seems fine | Measure resistance across the fan motor with the system off | Within the manufacturer's specified range (usually 1.5-3 ohms for a typical 1/3 HP motor) |
Applicable Rheem Models
- NCB(gas)
- NPE(electric)
- R801T(gas)
- R92E(electric)
- R92V(gas)
- RGE(gas)
- RH2T(electric)
- RNC(dual_fuel)
- RNE(electric)
- RNG(gas)
- RP16(electric)
- RPB(gas)
- RTGH(gas)
- Rheem Classic(gas)
- Rheem Classic 80 Plus(gas)
- Rheem Classic 80% Gas Furnace(gas)
- Rheem Classic 90 Plus(gas)
- Rheem Classic Plus Series(gas)
- Rheem Classic Series(dual_fuel)
- Rheem Prestige(gas)
- Rheem Prestige 95% Gas Furnace(gas)
- Rheem Prestige Series(gas)
Replacement Parts
| Part | OEM Number | Est. Cost | Where to Buy |
|---|---|---|---|
| Fan control board | RHEEM 340120 | — | Find Part |
| Fan motor | RHEEM 340130 | — | Find Part |
Related Codes on Same Models
Other codes that affect the same Rheem model families as A061.
| Code | Description | Severity |
|---|---|---|
| A001 | Ignition Failure | Warning |
| A021 | Over-Temperature | Warning |
| A031 | Inlet Thermistor Open/Short | Warning |
| A041 | Outlet Thermistor Open/Short | Warning |
| A043 | Water Level Error | Warning |
| A051 | Fan Motor Abnormality | Warning |
| A052 | Fan Motor Speed Error | Warning |
| A053 | Fan Motor Open Circuit | Warning |
| A054 | Fan Motor Overcurrent | Warning |
| A055 | Fan Motor Locked | Warning |